Professional Air Duct Installation Services in Tyler, TX
Our crew installs insulated flex duct where it fits best, using methods that keep it from sagging, kinking, or losing airflow. We size each flex run based on the airflow the room needs. Our technicians pull every run tight and cut it to length so there's no extra slack. Flex ducts are supported with wide straps every few feet. Turns are made with gentle bends or rigid elbows to keep air moving. Each connection is sealed with mastic and secured with clamps. We test airflow through every flex run when the installation is done. The specific air duct installation services we handle in Tyler are listed below.
Home Air Duct Installation in Tyler
Many older homes still run on original ductwork that was sized for a smaller AC unit or a floor plan that has since changed. Our technician measures every room, checks the existing trunk line and supply branches, and records the size of each register opening. We remove the old duct runs and install a new trunk and branch layout sized with Manual D calculations for your current system. Rigid sheet metal forms the main trunk, and insulated branch lines connect it to each room. Every takeoff and boot gets sealed with mastic before the ceiling registers go back in. Once the job is done, each bedroom and living area cools at the same pace.
New Air Duct Installation in Tyler
New homes and room additions need ductwork designed from scratch. Our team works from the builder's floor plans and runs a Manual J load calculation for every room before ordering materials. Installers set the supply plenum on the air handler, run the trunk line through the attic or floor joists, and cut in each branch takeoff at its planned location. We coordinate with your builder so the duct rough-in passes inspection before drywall goes up. A duct leakage test confirms the system meets code before final sign-off. The new home or addition starts with balanced airflow in every room on its first day, with home air duct cleaning available to keep the newly installed system free from dust and debris.
Air Conditioning Duct Installation in Tyler
A new AC unit often moves more air than the old ductwork was built to carry, which causes noisy registers and short cooling cycles. Our technician checks the blower capacity and static pressure rating of your new air conditioner before designing the duct connection. We size the supply and return plenums to match the unit's airflow and fit a transition that joins the plenum to the main trunk. Installers wrap each supply run in attic-rated insulation to stop condensation on the duct surface. AC duct cleaning can also help keep airflow paths clear after installation. A static pressure test after startup confirms the blower pushes air through the system within the manufacturer's range. Your new AC runs quieter and cools the house on shorter, even cycles.
Flexible Air Duct Installation in Tyler
Flex duct that sags, kinks, or runs longer than needed loses airflow before the air reaches the register. Our installer plans the shortest path from each takeoff to its room and pulls every flex run fully stretched. We support the duct with wide straps at close intervals so the inner core stays straight between hangers. Each end slides over its collar, gets a tie band on the inner core, and receives a mastic seal before the outer jacket is pulled over and strapped. Bends stay wide and gradual to keep the core from pinching. The finished flex runs deliver full airflow to every register they serve.
Air Duct Vent Installation in Tyler
Rooms with too few supply vents, or vents placed in the wrong spot, develop hot and cold zones within the same space. Our technician tests airflow in the room and marks new register locations based on window placement and furniture layout. We cut the ceiling or floor opening, install a sealed register boot, and connect it to a new branch line off the nearest trunk. The boot gets sealed to the drywall with mastic so attic air cannot leak into the room around the register. We fit an adjustable grille with a damper so you can fine-tune the airflow later. The room holds a consistent temperature across its full width.
Air Exchanger Duct Installation in Tyler
Tightly sealed homes trap stale indoor air and moisture unless a heat recovery or energy recovery ventilator exchanges it with fresh outdoor air. Our installer mounts the air exchanger in the attic or utility space and runs four dedicated duct lines to the unit. Two lines connect to exterior hoods for fresh air intake and exhaust, and two connect inside to the bathroom area and the main return. We keep the intake and exhaust hoods apart on the exterior wall so stale air does not re-enter the system. Every duct passing through unconditioned space gets insulated to stop condensation. After startup, we balance intake and exhaust airflow so the home gets a steady supply of fresh air without drafts.
Combustion Air Duct Installation in Tyler
Gas furnaces and water heaters inside closets or small utility rooms need a dedicated supply of outdoor air to burn fuel safely. Without that air, the appliance can pull air back down its flue and spill carbon monoxide into the home. Our technician measures the room volume and the appliance BTU rating to size the combustion air openings according to the fuel gas code. We run insulated duct from an outdoor wall or vented attic to high and low openings in the appliance room and cover each end with a screened grille. A combustion analyzer test after installation confirms the appliance burns cleanly with the new air supply. The furnace or water heater then operates safely with the door closed.
Return Air Duct Installation in Tyler
Homes with a single central return often starve the air handler, and closed bedroom doors trap supply air with no path back to the system. Our technician checks pressure in each closed room and identifies where a dedicated return or jumper duct is needed. We cut a return grille into the wall or ceiling and run an insulated duct back to the return plenum as part of professional HVAC ductwork installation. Each connection gets sealed so the return pulls air only from the living space and never from the attic. A filter grille at the main return keeps dust out of the new line. Bedrooms stay comfortable with the door closed, and the air handler pulls a full volume of air on every cycle.
Air Duct Installation Near Me in Tyler, TX
Homeowners looking for a local duct installer want a crew that knows area attic layouts and permit rules. Tyler Air Duct Cleaning serves Tyler and nearby areas including Azalea District, Hollytree, and The Cascades with new duct systems, replacements, and vent additions. Call (903) 623-8603 to get a written quote on your air conditioning duct installation cost.
About Our City Tyler
Residents and businesses throughout Tyler can rely on our team for air duct cleaning and ventilation-care services. We proudly serve local areas such as Azalea District, Hollytree, and The Cascades, helping customers address dusty registers, buildup inside accessible ducts, and questions about system cleanliness. Our work centers on thorough inspection and cleaning of relevant duct and vent components, giving property owners a straightforward way to maintain their heating and cooling air pathways. Each property is different, so our cleaning approach considers the condition of its ductwork.
Air Duct Installation Cost in Tyler, TX
Duct installation prices depend on the home's square footage, the number of supply runs, and how easy the attic or crawl space is to work in. A full duct system for an average-sized home usually runs between $4,000 and $9,000, while adding a single new run costs far less. Tyler Air Duct Cleaning starts pricing, and every project comes with a written quote based on Manual J and Manual D calculations.
| Service | What's Included | Typical Cost |
|---|---|---|
| Whole-home duct system | Load calculation, duct design, trunk and branches, leakage test | $4,000 to $9,000 |
| New construction ductwork | Rough-in, plenum, inspection coordination | $3,000 to $8,000 |
| AC duct connection | Plenums, transition, static pressure test | $800 to $2,000 |
| Flexible duct run | Insulated flex, collars, strapping, sealing | $250 to $600 per run |
| New supply vent | Boot, branch line, register | $300 to $700 per vent |
| Air exchanger ducting | Four duct lines, exterior hoods | $1,200 to $2,500 |
| Combustion air duct | Opening sizing, insulated duct, grilles | $400 to $1,000 |
| Return air duct | Grille, insulated return, plenum connection | $400 to $900 |
